Bathroom & Shower Tile Installation in Scottsdale, AZ
Leak-proof Custom Showers Since 2000| Free Estimate – ROC#334011
You use your shower every single day, so it has to hold up. Setting the tile is the easy part. The hard part is what goes on behind it, and that’s where a lot of showers go wrong. Get the prep and the waterproofing right, and a shower stays watertight for 20 years.
We’re Unique Contractor Co LLC, and we’ve been doing bathroom and shower tile installation in Scottsdale, Arizona since 2000. We’re licensed and insured tile contractor (ROC#334011). We build custom walk-in showers, tub surrounds, and full bathroom floors that last. Every job gets a proper waterproof membrane, a level surface, and sealed grout.
Call (480) 608-4343 for a free in-home estimate. We serve Scottsdale, Paradise Valley, Mesa, Chandler, Tempe, and the greater Phoenix Valley.
What Scottsdale Homeowners Say About Our Work
Why Shower Tile Work Is Different
Shower tile is the hardest tile job in your home. Here is why.
Tile and grout are not waterproof. Water passes through grout lines over time. If there is no waterproof layer behind the tile, that water reaches your wall studs and subfloor. Then you get mold, rot, and a repair bill far bigger than the original job.
Most shower failures trace back to skipped prep. A missing membrane. A flat shower pan with no slope. Cement board treated like it is waterproof when it is not. We do not skip these steps. We follow TCNA (Tile Council of North America) methods on every shower, so your bathroom stays dry behind the walls.
Our Bathroom & Shower Tile Services
We handle every part of bathroom and shower tile installation:
Custom walk-in shower tile
Floor-to-ceiling tile with proper slope and drainage.
Shower wall tile installation
Subway tile, large-format, and mosaic patterns.
Shower floor & pan tile
Slip-resistant mosaic and textured tile that actually drains.
Tub surround tile
Clean, watertight tile around your bathtub.
Bathroom floor tile installation
Porcelain and ceramic floors built for daily moisture.
Shower niche & bench tile
Built-in shelves and seats, fully waterproofed.
Curbless & walk-in designs
Zero-threshold showers with a clean, modern look.
Shower tile repair & replacement
Fixing cracked tile, loose tile, and failing grout.
Tile Materials We Install
Arizona’s dry air, hard water, and heat are tough on tile. We help you pick a material that holds up here and fits your budget.
Porcelain Tile
The top pick for Scottsdale showers. Porcelain is dense, nearly waterproof, and easy to clean. It comes in large-format, wood-look, and marble-look styles.
Ceramic Tile
A budget-friendly choice for shower walls and bathroom floors. Glazed and textured ceramic gives you good grip and a wide range of looks.
Natural Stone, Marble & Travertine
The high-end look you see in Paradise Valley, Arcadia, DC Ranch, and Silverleaf. Stone is gorgeous, but it needs a good sealer to stand up to Scottsdale's hard water and keep looking right.
Glass & Mosaic Tile
Great for accent strips, niches, and shower floors. The small mosaic pieces grip better underfoot and give the shower a custom touch.
Subway Tile
The rectangular subway shape has stayed popular for over a century for a reason. It suits full shower walls or a simple vanity backsplash, and it fits nearly any budget without looking cheap.
Our Proven Shower Tile Installation Process
Step 1
Consultation and layout
We measure your space, talk through material options, and map out a tile layout that minimizes awkward cuts and small slivers.
Step 2
Surface prep
We check the subfloor or wall framing for damage, then install cement board or another approved backer to create a stable, flat surface.
Step 3
Waterproofing
For any wet area, we apply a waterproofing membrane and build or reinforce the shower pan so water drains correctly instead of soaking into the walls or floor.
Step 4
Dry-fit and layout marking
Before any tile is set permanently, we dry-lay the pattern to confirm spacing, alignment, and any custom cuts around fixtures or niches.
Step 5
Setting the tile
Each tile goes into thin-set mortar with full coverage and back-buttering. No hollow spots, no lippage.
Step 6
Grouting and sealing
Once the tile has cured, we apply grout, clean the joints, and seal both the grout and any natural stone to protect against moisture and staining.
Step 7
Final details
Niches, shelves, edge trim, and transitions get finished last, so every edge is clean and every surface is ready for daily use.
Bathroom & Shower Tile Installation Cost in Scottsdale
Cost depends on the size of your shower, the tile you pick, and the prep your bathroom needs. Waterproofing, tear-out, and pattern all affect the price. The table below shows typical installed price ranges in the Scottsdale and Phoenix market.
Project Type | Typical Installed Cost | Timeline |
|---|---|---|
Bathroom floor tile | $7 – $20 / sq ft | 1 – 2 days |
Standard walk-in shower | $2,500 – $5,500 | 3 – 5 days |
Custom / large-format shower | $5,500 – $10,000+ | 5 – 10 days |
Natural stone / marble shower | $8,000 – $15,000+ | 1 – 2 weeks |
Waterproofing adds about $450–$750 to a shower. Tear-out of old tile runs $2–$5 per square foot. We give you an itemized quote — material, labor, and extras listed separately — so there are no surprises.
Why Scottsdale Homeowners Trust Us
26 years of local experience
We have built showers across the Valley since 2000.
Licensed & insured
We're a licensed Arizona contractor, and we stand behind every job we complete.
Waterproofing on every shower
We never skip the membrane. It is the step that prevents leaks.
Clear communication
You'll know your timeline, your material options, and your cost before work ever begins.
Free, honest estimates
We tell you the real cost before we start. No hidden fees.
Clean job sites
We protect your home and clean up at the end of every day.
Areas We Serve
Based in Scottsdale, we install bathroom and shower tile across Maricopa County:
- North Scottsdale
- South Scottsdale
- Old Town Scottsdale
- Paradise Valley
- Arcadia
- Mesa
- Chandler
- Tempe
- Cave Creek
- Carefree
- Fountain Hills
- Salt River Pima
Frequently Asked Questions
Most shower tile installations in Scottsdale cost $2,500 to $8,000. A standard walk-in shower runs $2,500 to $5,500. Custom showers with large-format or natural stone tile cost more. The final price depends on shower size, tile choice, and prep work.
A standard walk-in shower takes 3 to 5 days. That includes demolition, waterproofing, tile setting, grouting, and sealing. Waterproofing needs about a day to cure before tile goes up. Larger or custom showers can take 1 to 2 weeks.
Yes, always. We install a bonded waterproof membrane, such as Schluter Kerdi or RedGard, behind every shower. Cement backer board and grout are not waterproof on their own. The membrane is what keeps water out of your walls and prevents mold. We never skip it.
Porcelain tile is the best choice for most Scottsdale showers. It is dense, nearly waterproof, and stands up to hard water and heat. Ceramic works well too and costs less. Natural stone and marble look stunning but need regular sealing to stay protected.
Often, yes. If the damage is small and the waterproofing behind it is still sound, we can replace cracked or loose tile and match your existing style as closely as possible. If water has gotten behind the wall, we usually recommend a full tear-out and a fresh waterproof base to protect your home.
Yes. We are a fully licensed and insured tile contractor serving Scottsdale since 2000, under Arizona Registrar of Contractors license ROC#334011. Every job meets code, and your home is fully covered.
Ready for a Shower That Lasts? Get Your Free Estimate
A new tile shower or bathroom floor can transform your home. Work with a licensed pro who does it right the first time. Call (480) 608-4343 or request your free in-home estimate today. We will come to you, look at your space, and give you an honest price.